澳洲应急灯AS2293.3测试流程

应急灯的产品进入澳洲市场的能效测试。进入澳洲市场的应急灯产品，现在大多数买家还会要求供应商提供AS2293.3的测试报告。

　　一、测试标准及内容

　　1.测试标准：

　　AS 2293 Emergency escape lighting and exit signs for buildings

　　ASmdash;2005 Part 3: Emergency escape luminaires and exit signs （应急逃生灯具和出口标志）测试标准

　　ASmdash;2005 Part 1: System design, installation and operation （系统的设计、安装和运行）

　　AS/NZSPart 2: Inspection and maintenance （检查和维护）

　　2.测试内容：

　　AS2293.3的测试项目为应急照明等级、照明启动（冷热启动）、颜色与亮度、电池系统高低温充放电测试，与其他一些小的测试。

　　应急照明等级：

　　这个测试客户需求高，通常澳洲买家都会要求产品资料中标出应急照明等级。因为应急照明等级对于产品的安装非常重要，在AS2293.1里面安装设计需要用到，通过这个等级能有效的计算出产品安装高度与产品安装间距（推算出这个房子需要安装多少个这种应急灯），从而达到建筑上对应急灯有效的利用和安装设计。应急照明等级是根据我们的测试结果，通过计算来进行判定。

　　二、测试流程

　　客户提供产品基本信息（系列产品提供差异表）与资料（电池规格书）及符合数量要求的样品。

　　LCS进行开案。开案时请注意，如果是单项测试，需要备注是哪个测试项目。

　　然后工程受理项目，安排测试，完成报告

　　AS2293.3报告不需要注册。因此提交报告即完成项目。

　　三、周期

　　单项：

　　光学性能：

　　应急照明等级需要3个工作日一款

　　照明启动需要3个工作日一款

　　颜色与亮度（仅对出口标志产品）需要5-7个工作日一款

　　电池系统性能：

　　高低温充放电测试需要10-15工作日一款

　　全项目：

　　主测产品，一款需要15-25个工作日（出口标志的测试多一个项目，周期会相对长一些）。

　　系列测试，如果是增加光学性能测试，可与主测产品同步，无需增加周期，如果是增加电池系统能效测试，需要增加10-15个工作日。

　　以上项目如需出报告要增加2个工作日。

　　四、具体报价和样品准备请联系立讯曾先生

　　AS2293.3 从2005升级到2018版本了，具体升级的内容，

　　updated from ASto AS/NZS

　　Changes in this edition of the Standard include the following:

　　(a) Introduction of requirements for alternative light sources (i.e. LED) and allowance for

　　the use of emerging battery technologies.

　　(b) Inclusion of New Zealand requirements (for publication as AS/NZS Standard).

　　(c) Updated references to new pictogram standards.

　　(d) Added definition and requirements for dual function exit signs.

　　(e) Replacement of AS 3137 with AS/NZS

　　Some details:

　　1. Dual function exit signs shall firstly comply with all the requirements of the subsequent clauses 3.3 and 3.4 of this Standard in order to then be classified as an emergency luminaire.。

　　2. All emergency luminaires and exit signs shall comply with AS/NZSunless otherwise varied in this Standard.

　　3. Specific requirements relating to Clauses F6 and F8 of the New Zealand Building Code have been added where it is necessary to alter clauses of this Standard to comply with New Zealand requirements.

　　4. Additional requirements of marking：

　　a) Where combined or sustained emergency luminaires are used, the location of the emergency light source shall be clearly marked, together with any information necessary to ensure correct light source replacement.

　　b) Designed mounting positions and orientation (related to luminaire position/ safety IP rating, etc.). This information shall be marked on the luminaire to enable identification of the classification for each mounting position.

　　c) For LED exit signs the body shall also be marked with the Projected Light Source Life.

　　5. Add new clause for particular requirements for centrally supplied emergency luminaires and exit signs。

　　6. New test requirement:

　　a) Glare limitations：

　　In order to restrict disability glare at higher angles, limitations are applied to the luminous intensity of the luminaire based on the mounting height range in accordance with Table C1.

　　b) Colour temperature and colour rendering index：

　　The colour temperature shall fall with the range from 2500 K to 7000 K.

　　The minimum value of the colour rendering index Ra of the light source utilized in any emergency luminaire shall be greater than 40.

　　c) LED:

　　measure LED Ts temperature and operating current at 40.

　　d) PROJECTION OF LIGHT SOURCE LIFE (LSL) IN LED EXIT SIGNS:

　　LM-80 test report for LED should be provided and LM-80 data for the LED being assessed,based on IES TM-21,calculate the life of LED exit signs.